Search Results

An investigation was conducted to determine the fore and aft elastic response characteristics and footprint geometrical properties of 30 × 11.5 −14.5, Type VIII, bias-ply and radial-belted aircraft tires. Stiffness and damping characteristics of each tire were obtained from load-deflection curves generated from static tests. Tire footprints were obtained for various vertical loads, and geometrical measurements were obtained from the resulting silhouettes. Results of this investigation show considerable differences in stiffness and damping characteristics between the bias-ply and radial-belted tire designs. Footprint geometrical data indicate that footprint aspect ratio effects may interfere with improved hydroplaning potential associated with the radial-belted tire operating at higher inflation pressures. Tire-wheel slippage problems encountered when testing the radial-belted tire design required special attention.

Airplane flight tests have been conducted to determine the effects of wing leading-edge modifications and a ventral fin addition on the spin resistance of a typical high-wing, single-engine, general aviation airplane. Drooped wing leading-edge modifications which improve lateral stability at high angles of attack were tested in combination with a ventral fin that improves directional stability. Each modification was evaluated using spin resistance criteria which have been proposed for incorporation into the Federal Aviation Regulations for certification of light aircraft. The best configuration tested, a combination of outboard wing leading-edge droop and a ventral fin, provided a very significant increase in overall airplane spin resistance, but was not sufficient to satisfy all requirements of the spin resistance criteria.

The ability of modern airplane surfaces to achieve laminar flow over a wide range of subsonic and transonic cruise flight conditions has been well-documented in recent years. Current laminar flow flight research conducted by NASA explores the limits of practical applications of laminar flow drag reduction technology. Past laminar flow flight research focused on measurements of transition location, without exploring the dominant instability(ies) responsible for initiating the transition process. Today, it is important to understand the specific causes(s) of laminar to turbulent boundary layer transition. This paper presents results of research on advanced devices for measuring the phenomenon of viscous Tollmien-Schlichting (T-S) instability in the flight environment. In previous flight tests, T-S instability could only be inferred from theoretical calculations based on measured pressure distributions.

The LIDAR In-Space Technology Experiment (LITE) will employ LIDAR techniques to study the atmosphere from space. The LITE instrument will be flown in the Space Shuttle Payload Bay with an earth directed orientation. The experiment thermal control incorporates both active and passive techniques. The Laser Transmitter Module (LTM) and the System Electronics will be actively cooled through the shuttle pallet coolant loop. The Receiver System and Experiment Platform will be passively controlled through the use of insulation and component surface properties. This paper explains the thermal control techniques used and the analysis results, with primary focus on the Receiver System.

Market growth and technological advances are expected to lead to a new generation of long-range transports that cruise at supersonic or even hypersonic speeds. Current NASA/industry studies will define the market windows in terms of time frame, Mach number, and technology requirements for these aircraft. Initial results indicate that, for the years 2000 to 2020, economically attractive vehicles could have a cruise speed up to Mach 6. The resulting research challenges are unique. They must be met with new technologies that will produce commercially successful and environmentally compatible vehicles where none have existed. Several important areas of research have been identified for the high-speed civil transports. Among these are sonic boom, takeoff noise, thermal management, lightweight structures with long life, unique propulsion concepts, unconventional fuels, and supersonic laminar flow.

Large space structures will be a key element of our future space activities. They will include spacecraft such as the planned Space Station and large antenna/reflector structures for communications and observations. These large structures will exceed 100 m in length or 30 m in diameter. Concepts for construction of these spacecraft on orbit and their materials of construction provide some unique research challenges. This paper will provide an overview of our research in space construction of large structures including erectable and deployable concepts. Also, an approach to automated, on-orbit construction will be presented. Materials research for space applications focuses on high stiffness, low expansion composite materials that provide adequate durability in the space environment. The status of these materials research activities will be discussed.

Although the number of possible applications of boundary-layer control is large, a discussion is given only of those that have received the most attention recently at NASA Langley Research Center to improve airfoil drag characteristics. This research concerns stabilizing the laminar boundary layer through geometric shaping (natural laminar flow, NLF) and active control involving the removal of a portion of the laminar boundary layer (laminar flow control, LFC) either through discrete slots or a perforated surface. At low Reynolds numbers, a combination of shaping and forced transition has been used to achieve the desired run of laminar flow and control of laminar separation. In the design of both natural laminar flow and laminar flow control airfoils and wings, boundary layer stability codes play an important role. A discussion of some recent stability calculations using both incompressible and compressible codes is given.

On December 1, 1984, the National Aeronautics and Space Administration (NASA) and the Federal Aviation Administration (FAA) conducted the first remotely-piloted air-to-ground crash test of a transport category aircraft. The Full-Scale Transport Controlled Impact Demonstration (CID) was the culmination of four years of effort by the two agencies. NASA and the FAA had many objectives during the joint planning and conduct of the Controlled Impact Demonstration. NASA's interest was primarily structural crashworthiness. The FAA's primary interest was the demonstration of an antimisting fuel additive's performance. Demonstration of improved crashworthy design features was a secondary objective for the FAA. This paper is a report on the NASA experiments conducted during the CID. A portion of the preliminary structural loads data was released to the public at a Government/Industry CID Workshop held April 10, 1985, at Langley Research Center, Hampton, Virginia.

Results are presented of an experimental and analytical study of the dynamic response to crash loadings of five different load-limiting subfloors for general aviation aircraft. These subfloors provide a high-strength structural floor platform to retain the seats and a crush-able zone to absorb energy and limit vertical loads. Experimental static load-deflection data and dynamic deceleration response data for the five subfloors indicated that the high-strength floor platform performed well in that structural integrity and residual strength was maintained throughout the loading cycle. The data also indicated that some of the subfloor crush zones were more effective than others in providing nearly constant load for a range of displacement. The analytical data was generated by characterizing the nonlinear crush zones of the subfloor with static load-deflection data and using the DYCAST nonlinear finite element computer program.

An overview is given of the ongoing joint NASA/FAA/Industry Surface Traction And Radial Tire (START) Program being conducted at NASA Langley's Aircraft Landing Dynamics Facility (ALDF). The START Program involves tests using three different tire sizes to evaluate tire rolling resistance, braking, and cornering performance throughout the aircraft ground operational speed range for both dry and wet runway surfaces. Preliminary results from recent 40 x 14 size bias-ply, radial-belted, and H-type aircraft tire tests are discussed. The paper concludes with a summary of the current program status and planned ALDF test schedule.